Description
You may also like Upgraded ATS-20+ Radio Receiver FM AM (MW & SW) SSB (LSB & USB) With Battery 53.0 USD 55.79 USD Free shipping 5% off Usdr usdx+ Plus Transceiver 3W-5W All Mode 8 Band HF Ham Radio Transceiver 143.79 USD Free shipping Usdr usdx+Plus 8 Band SDR Full Mode HF Ham RadioSSBQRP Transceiver Upgrade Y 156.79 USD Free shipping SDR Receiver Switch Antenna Share Transceiver Switch Box 100W DC 160MHz US Plug 70.79 USD Free shipping Upgraded ATS-25X1 All Band DSP Radio Receiver FM LW MW SW With 2.4" Touch Screen 109.79 USD Free shipping Development Board 35M-4400M RF Signal Source Phase Locked Loop Generation Module 33.05 USD 34.79 USD Free shipping 5% off ATS25AMP Si4732 Full Band Radio Receiver FM RDS AM LW MW SW SSB DSP Receiver 135.65 USD 142.79 USD Free shipping 5% off Usdr usdx+ Plus Transceiver SDR QRP CW All Mode 8 Band w/Power Adapter US Plug Y 161.3 USD 169.79 USD Free shipping 5% off USDX USDR HF QRP SDR Transceiver SSB/CW Transceiver 8-Band 5W DSP SDR Black Shell US Plug With Mic Software: https://github.com/threeme3/QCX-SSB/tree/feature-rx-improved Description: This is a shortwave druse ssb/cw transceiver. It has 1602 screen, built-in battery, equipped with charger, built-in microphone, built-in speaker! It can be connected to an auto key and can be cw decoded. Characteristics: -Using Osmo series launch tube, durable -Can be used by connecting the antenna (M seat) -8 bands. Power wave digital display! 13.8v 10w maximum external power! Built-in 12.6v battery -Dimensions: 76x46x130mm/3x1.8x5.1" -Provides FT8 option connector later -Use tcxo for kds. Accuracy 0.5ppm (1ppm per year) - Aluminum shell laser marking -Fully aluminum buttons! Translucent silica gel button (receive green, emit red) Function list: - Simple, interesting and versatile cxp ssb HF transceiver with built-in dsp and sdr functions - EER electronic level driven SSB launch stage - 13.8v power supply provides about 10w ssb output -Full mode support: usb, lsb, cw, am, fm -dsp filter: password 4000, 2500, 1700, 500, 200, 100, 50hz - DSP Function: Auto Gain Control (AGC), Noise Reduction (NR), Voice Trigger, Xmit Voice Trigger (VOX), Attenuator RX Attenuator (ATT), TX Noise gate, TX driver control, volume control, dbm/s meter - Sideband Reverse SSB/Carrier Suppression: better than -45dbc, imd3 (two tone) -33dbc, reception: better than -50dbc -Multi-band support, continuously adjustable in 160m-10m frequency band (and 20khz..99mhz performance loss) -Open source, integrated firmware for Arduino IDE; allows experimentation, can add new functions, can share contributions via github, software complexity: 2000 lines of code -Software based VOX can be used as a quick and full raid (QSK and Semi-QSK operation), or to assist in running in digital mode (no cat or ptt interface) for rx/tx switching, external delayed ptt output control tx/pa -Simple installation modification with 8 component changes and 8 wires -Lightweight and cost-effective transceiver: thanks to the level and eer transmitter, it has high energy efficiency (no bulky heat sink needed) and simple Design (no complex balanced linear power amplifiers required) -SSB transmitter stage entirely based on digital and software: by controlling the phase of the PLL SI5351 (through the small frequency shift of I2C above 800kbit/s) and the amplitude of the PA (through the PWM of PWM) to sample the microphone input and reconstruct the ssb signal. Pa key shaping circuit) -Software-based, all-digital SDR receiver stage (optional): samples the I/Q (complex) signal from the digital mixer from the square sampling detector, and perform a 90 degree phase shift in the software (hilber transform) and eliminate one by adding sidebands -Three independently switchable analog front receiver faders (0db,-13db,-20db,-33db,-53db,-60db,-73db) - MDS receiver noise level: -135 dbm (200hz bw) to 28mhz - Receiver front selectivity: Steep tuning frequency -45db/ten times roll-off/-2khz - Lock dynamic range: 20khz offset 123db, 2khz offset 78db - CW decoder, straight/iambic-a/b keyboard -Vfo a/b scrit and split, and switch the corresponding relay band filter via i2c -Support for cat (TS480 subset), you can stream audio, press keys and display text through cat -This is probably the most economical and easiest to build standalone SDR/SSB transceiver. Great simplification simplifies the original QCX circuit (i.e. reduces installation components by 50%, reduces installation components by 50%, does not require complex transformer windings and does not require alignment procedures), and is more versatile Port introduction: -Charge: Built-in lithium battery charging port and you can only use the charger provided! It is forbidden to use other chargers! -Switch: off to turn off. Bat: Built-in battery power supply. 13.8: external power supply -DC13.8v/3a: external power supply port -Key: Automatic key body connection (A, B, single key) -Pa: external power amplifier, PTT signal -Microphone: External microphone port -Uart: serial communication port (osmo compatible) -Spk: external speaker Package included: 1 x Transceiver 1 x Power Adapter 1 x Mic 1 x 3 in 1 screwdriver About US Our shop has been a ebay member since 2008 in USA ,with a long history,a solid basic and rich experience. We are focus on Auto Parts,Car Parts,Motorcycle Parts,3C,other hot sale items and so on. We Appreciate every customer, We will do our best to serve each customer. We aim to provide to customers high quality product and best service. About Shipping&Returns The item usually will be dispatched within 5 Days after your payment, but it usually takes 3-10 working days to delivery depends on buyers' address or other majeure on the way. If you are not satisfied with the items and want to return the item,we hope you could message us first,we will give you the return details, we think we could give you the best service to save your time and money.Thank you. About Feedback&Customer Service If you are enjoy your shopping here,not only enjoy the items but also the service,we are appreciate if you could give us a 5-star feedback. If you are not satisfied with the item,before you give us the negative feedback,we hope we could give you the best solution through our commutication. We think we could do it if you give us the chance.Thank you.